#Download msa device discovery tool serial#
#Download msa device discovery tool driver#
#Download msa device discovery tool software#

If you do not remove or disable access to the Prohibited Content within 2 business days of our notice, we may remove or disable access to the Prohibited Content or suspend the Services to the extent we are not able to remove or disable access to the Prohibited Content. If we reasonably believe any of Your Content violates the law, infringes or misappropriates the rights of any third party, or otherwise violates a material term of the Agreement (including the Service Terms, or the Acceptable Use Policy) (“Prohibited Content”), we will notify you of the Prohibited Content and may request that such content be removed from the Services or access to it be disabled.

#Download msa device discovery tool software#

In connection with your use of the Services, you are responsible for maintaining licenses and adhering to the license terms of any software you run. You will reasonably cooperate with us to identify the source of any problem with the Services that we reasonably believe may be attributable to Your Content or any end user materials that you control.ġ.4. You will provide information or other materials related to Your Content (including copies of any client-side applications) as reasonably requested by us to verify your compliance with the Agreement. You may not transfer outside the Services any software (including related documentation) you obtain from us or third party licensors in connection with the Services without specific authorization to do so.ġ.2. You must comply with current technical documentation applicable to the Services (including applicable user, admin, and developer guides) posted on the AWS Site at (and any successor or related locations designated by us).ġ.3. The USB mini 5 male connector plugs into the CLI port as shown in Figure 27 (generic controller module is shown).1.1. Use the provided USB cable to connect controller A to a USB port on a host computer. Record these IP addresses so that you can specify them whenever you manage the controllers using the SMU or the CLI.Ģ. From your network administrator, obtain an IP address, subnet mask, and gateway address for controller A, and another for controller B. NOTE: Changing IP settings can cause management hosts to lose access to the storage system.ġ. Be sure to change the IP address via the SMU before changing the network configuration. Once new IP addresses are set, you can change them as needed using the SMU. Use the CLI commands described in the steps below to set the IP address for the network port on each controller module. The USB cable and CLI port support USB version 2.0.

#Download msa device discovery tool serial#

The command-line interface enables you to access the system using the USB (universal serial bus) communication interface and terminal emulation software.

Gateway IP Address: 10.0.0.1 If the default IP addresses are not compatible with your network, you must set an IP address for each network port using the command-line interface embedded in each controller module.

Management Port IP Address: 10.0.0.2 (controller A), 10.0.0.3 (controller B).

Network ports on controller module A and controller module B are configured with the following factory-default IP settings:

#Download msa device discovery tool driver#

For Windows systems see 'Downloading a device driver for Windows computers' (page 39). NOTE: For Linux systems, see 'Preparing a Linux computer before cabling to the CLI port' (page 39). If you have not done so already, you need to enable your system for using the command-line interface port. If you did not use the MSA Device Discovery Tool to set network port IP values, set them manually using the command-line interface port and cable. Setting network port IP addresses using the CLI port and cable

If you do not have a DHCP server, you will need to ask your system administrator to allocate two IP addresses, and set them using the command-line interface during initial configuration (described below). Use a ping broadcast to try to identify the device through the ARP table of the host. Look in the DHCP server's pool of leased addresses for two IP addresses assigned to 'HP MSA Storage.'Ģ. Setting network port IP addresses using DHCPġ. Alternatively, you can set network port IP addresses using the command-line interface on HP-UX, Windows, and Linux platforms. Record these IP addresses so that you can specify them whenever you manage the controllers using the SMU or the command-line interface. Follow the instructions to discover the IP addresses of the controller or controllers.

Insert the DVD into the drive on a Linux or Windows computer on the network that is connected to yourĬontroller enclosure. Locate the DVD included with your MSA 2040 storage device.